How To Bend Tubes and Frames by Yourself - MotoMatter
How To Bend Tubes and Frames by Yourself

The How To page is for people who want to get their hands dirty, or are thinking about getting them all greased up.

Just watch, learn and ask. Before you know it, you are building your own beauty’s.
These posts will be a combination of collected information from the web and produced by our own.

In this post we help you with bending your own tubes and frames without spending a bunch of money on expensive tools.

The first thing that you should do (to prevent kinking the tube) is fill her up with sand. You could close both ends of the tube with welding, or by smashing them flat on both side or by some other creative way like a big metal plug.
Note: If you close the tube by welding, make sure the sand is dry (wet sand = turning your pipe into a pressure cooker = losing your face). Make sure the tube / pipe is filled to its maximum.

how to bend a tube

There are many ways to bend a tube and we will give you the low-budget ones!

#1 – The Fiesta (good for heavy bending and strong/big tubes)

I want to talk about Ford Fiestas. Yes, the small hatchback thingy with four wheels. Specifically, the ones between the J and N fiesta tube benderregistration marks.

What’s so great about these Fiestas? Well it turns out that the rear stub axle is held on by four bolts, and that the rear drum has, roughly speaking, a four inch radius. Four inches is by a fortunate coincidence about the radius that you want for bends in a motorcycle frame.

One of the most elusive pieces of equipment you’ll need for building or modifying frames is a tube bender. The hydraulic ones you see in tool supermarkets are in fact pipe benders and don’t do a very good job of bending tube. So I made one out of a Fiesta rear stub axle and hub and it seems to do a much better job of bending tube and shouldn’t cost more than £50 at the outside.

First catch your Fiesta. Remove one of the rear wheels, and then take the cap off of the centre of the brake drum and undo the nut that holds the drum/hub on and remove that keeping in mind that the left side one has a left hand thread. Behind the brake back plate there are four bolts that attach the stub axle to the beam, once these are undone you can remove the stub axle and leave the brake back plate on the car. You need the stub axle, the drum/hub, the stub axle mounting bolts, the drum/hub retaining nut and cover, and at least two of the wheel nuts. This bender should work for 1″, 1 1/8″, and 1 ¼” outside diameter tube, but you’ll need to make a former and slider for each size so it might pay to grab the other hub while you’re there.

Materials you need are about 14 feet of 40mm by 80mm by 3mm wall box section, a foot of 1 ¼” by 1 ¼” by 1/8″ wall box section, a foot of tube or pipe that will sleeve over the tube you want to bend, some ¼” plate and something about 6 feet long to make a handle out of as well as various other odds and sods.

Read more about it here (we did only take a piece of the story, to make this post more manageable)

#2 – The Wood Bender (Small) (good for light bending)

Here, I show a quick and dirty method to bend aluminum tubing. I am documenting how I built a new bow rail for my sailboat.

Step 1: Build the jig
Here, I trace the curve that I want on some scrap lumber. This scrap will be used to build the bending jig. I’m just using a couple of old tube bender2×4’s. Your wood should be somewhat thicker than the diameter of the tube you wish to bend.

Step 2: Cut the lumber
Just cut out the traced jig. Use a bandsaw if you have one. I don’t so, I just used a jigsaw. Cut the jig to be little smaller than the desired curve. This will allow for the spring action of the tubing. Since I used two pieces of 2×4, I made a little gusset to hold the two together (2nd pic). Hint: Add a little bevel inward on the bottom of the cut. This will keep the tubing from popping off of the jig when bending.

Step 3: Don’t bend like this
If you do this, then you will almost certainly get a kink in the tubing.

Step 4: Ready to bend
Here, you can see that I take a piece of scrap (from the earlier cut) and attach it to the table to complete the jig.

You will want to bend from one side only while ensuring the tubing is supported wile bending. While bending, try to keep the pressure against the jig instead of the tubing.

You may want to practice with some cheap amluminum conduit to get the hang of it. When you are ready, get the polished stuff.

Read more about it AND SEE ALL PICTURS here (we did only take a piece of the story, to make this post more manageable)

#3 – The Wood Bender (Big) (good for heavy bending)

A homemade stainless tubing bender, which was built for bending 7/8″ diameter 304 stainless steel tubing (3/64″ wall thickness). They needed a tubing bender to make a custom spray dodger (and possibly also a bimini top) for our 20′ cat ketch sailboat. Cost was about $50 in materials and 6 hours of labor. About half of the $50 was spent on plywood and bolts, and the other half was for the 7/8″ round nose router bit. Much cheaper and more effective than any of the other options they explored.

#4 – Small Tube Bender out of metal

#5 – Making your own Tube Bending Die

Some more information on wikipedia can be found here.

# 6 – Using a Cheap Bender

tube benderss

Well, these work actually pretty good IF you DO NOT want to make a too great bend. The tube will kink and you could prevent it A BIT by filling it up with sand, but that’s it. It will not work on thin exhaust tubes etc.
The plus side of these little machines: They are pretty cheap…

You could also choose to do it by hand (this only works with small, light, thin tubes) with a tool like this one.

We hope this gave you some inspiration on how to bend tubes for your cafe racer projects!

[Edit] We found this one on the web as well. Very nice and simple 🙂


Building a Cafe Racer Yourself?

Sign up for our newsletter

Stay up to with the MotoMatter Newsletter. With this newsletter you will receive the latest Motorcycle News, Events, How-to ’s, Videos, Promotions and much more.

The subscription can be terminated at any time by unsubscribing in our newsletter. We refuse to disclose your data to third parties. You will receive an e-mail confirmation after the subscription. So we make sure that no unauthorized person can register you in our newsletter.